Connect-Tek Transa PRO 17 Manual de Instruções Página 65
- Página / 92
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
61
Chapter 8 Specifications
Power
90–264VAC, 47–63Hz, 15VA, 7W maximum
11–26 VAC/VDC, 15VA, 7W maximum
Input 1 resolution: 18 bits
Sampling rate: 5x/second
Maximum rating: -2VDC minimum, 12VDC maximum
(1 minute for mA input)
Temperature effect: ±1.5uV/°C for all inputs except mA
input ±3.0uV/°C for mA input
Sensor lead resistance effect:
T/C: 0.2uV/ohm
3-wire RTD: 2.6°C/ohm of resistance difference of two leads
2-wire RTD: 2.6°C/ohm of resistance sum of two leads
Common mode rejection ratio (CMRR): 120dB
Normal mode rejection ratio (NMRR): 55dB
Sensor break detection:
Sensor open for TC, RTD, and mV inputs, below 1mA for
4–20mA input, below 0.25V for 1–5V input, unavailable for
other inputs.
Sensor break responding time:
Within 4 seconds for TC, RTD, and mV inputs, 0.1 second for
4–20mA and 1–5V inputs.
Characteristics:
Input 2
Resolution:
18 bits
Sampling rate: 1.66 times/second
Maximum rating: -2VDC minimum, 12VDC maximum
Temperature effect: ±3.0uV/°C for mA input ±1.5uV/°C
for all other inputs
Common mode rejection ratio (CMRR): 120dB
Sensor break detection: Below 1mA for 4–20mA input,
below 0.25V for 1–5V input,
unavailable for other inputs.
Sensor break responding time: 0.5 seconds
Characteristics:
Input 3 (event input)
Logic low:
-10V minimum, 0.8V maximum.
Logic high: 2V minimum, 10V maximum
External pull-down resistance: 400KΩ maximum
External pull-up resistance: 1.5MΩ minimum
Functions: select second set point and/or PID, reset alarm 1
and/or alarm 2, disable output 1 and/or output 2,
remote lockout.
Output 1/Output 2
Relay rating:
2A/240 VAC, life cycles 200,000 for resistive
load
Pulsed voltage: source voltage 5V, current limiting resist-
ance 66Ω.
Linear output characteristics:
Linear Output
Resolution:
15 bits
Output regulation: 0.01% for full load change
Output settling time: 0.1 second (stable to 99.9%)
Isolation breakdown voltage: 1000VAC
Temperature effect: ±0.0025% of SPAN/°C
- Instruction Manual 1
- TEC-9300 1
- Self-Tune Fuzzy / PID Process 1
- Temperature Controller 1
- Chapter 1 Overview 5
- Related Products 6
- 1–2 Ordering Code 6
- Figure 1. Access Hole 7
- Overview 7
- Table 1.1 DIP Switch 7
- Configuration 7
- 1–4 Keys and Displays 8
- 1–6 System Modes 11
- 1–7 Parameter Description 12
- Chapter 2 Installation 19
- 2–6 Thermocouple Input Wiring 20
- 2–4 Power Wiring 20
- 2–7 RTD Input Wiring 21
- 2–8 Linear DC Input Wiring 21
- 2–10 Event Input wiring 23
- 2–11 Output 1 Wiring 24
- 2–12 Output 2 Wiring 25
- Figure 2.19 RS-232 Wiring 28
- 3–1 Input 1 29
- 3–2 OUT1 and OUT2 Types 30
- 3–3 Configuring User Menu 30
- 3–4 Heat Only Control 30
- 3–5 Cool Only Control 31
- 3–6 Heat-Cool Control 32
- 3–7 Dwell Timer 33
- 3–8 Process Alarms 34
- 3–9 Deviation Alarm 35
- 3–10 Deviation Band Alarm 36
- 3–11 Heater Break Alarm 37
- 3–12 Loop Break Alarm 37
- 3–13 Sensor Break Alarm 38
- 3–14 SP1 Range 38
- 3–15 PV1 Shift 38
- 3–16 Failure Transfer 39
- 3–17 Bumpless Transfer 40
- 3–18 Self tuning 40
- Self-tune Menu 40
- 3–19 Auto tuning 41
- 3–20 Manual Tuning 42
- 3–21 Signal Conditioner 43
- DC Power Supply 43
- 3–22 Manual Control 43
- 3–23 Display Mode 44
- 3–25 Reload Default Values 44
- 4–1 Event Input 45
- 4–2 Second Set Point 45
- 4–3 Second PID Set 46
- 4–4 Ramp and Dwell 46
- 4–5 Remote Set Point 47
- 4–6 Differential Control 47
- 4–7 Output Power Limits 48
- 4–8 Data Communication 48
- 4–9 Analog Retransmission 49
- 4–10 Digital Filter 49
- 4–11 Sleep Mode 49
- 4–12 Pump Control 50
- 4–13 Remote Lockout 50
- Chapter 5 Applications 51
- 5–3 Heat Only Control 52
- 5–5 Heat-Cool Control 53
- 5–4 Cool Only Control 53
- 5–6 Ramp and Dwell 54
- 5–7 Remote Set 55
- 5–8 Differential Control 55
- 5–9 Dual Set Point/PID 56
- 5–10 RS-485 57
- 5–11 RS-232 58
- 5–12 Retransmit 58
- Chapter 6 Calibration 59
- Troubleshooting procedures: 61
- Chapter 8 Specifications 65
- PID: Fuzzy logic modified 66
- 9-1 Functions Supported 67
- 9-2 Exception Responses 68
- 9-3 Parameter Table 69
- P= 100.0 80
- 9-3 Communication Examples 80
- A–1 Menu Existence Conditions 81
- A–2 Factory Menu Description 84
- A–3 Glossary 85
- A–4 Memo 89
- A–5 Warranty 91
- TEMPCO’s Visionary Solutions 92
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.026 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais