Connect-Tek Transa PRO 17 Manual de Instruções Página 39
- Página / 92
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
35
3–16 Failure Transfer
The controller will enter failure mode if one of the following conditions occurs:
1. SB1E occurs (due to input 1 sensor break or input 1 current below 1mA if
4–20mA is selected or input 1 voltage below 0.25V if 1–5V is selected) if PV1,
P1-2, or P2-1 is selected for PVMD or PV1 is selected for SPMD.
2. SB2E occurs (due to input 2 sensor break or input 2 current below 1mA if
4–20mA is selected or input 2 voltage below 0.25V if 1–5V is selected) if PV2,
P1-2, or P2-1 is selected for PVMD or PV2 is selected for SPMD.
3. ADER occurs if the A-D converter of the controller fails.
Output 1 and output 2 will perform the failure transfer function as one of the fol-
lowing conditions occurs:
1. During power starts (within 2.5 seconds).
2. The controller enters failure mode.
3. The controller enters manual mode.
4. The controller enters calibration mode.
Output 1 failure transfer, if activated, will perform:
1. If output 1 is configured as proportional control (PB1≠0), and BPLS is selected
for O1FT, then output 1 will perform bumpless transfer. Thereafter, the previous
averaging value of MV1 will be used for controlling output 1.
2. If output 1 is configured as proportional control (PB1≠0), and a value of 0 to
100.0% is set for O1FT, then output 1 will perform failure transfer. Thereafter,
the value of O1FT will be used for controlling output 1.
3. If output 1 is configured as ON-OFF control (PB1≠0), then output 1 will be driv-
en OFF if O1FN selects REVR and be driven ON if O1FN selects DIRT.
Output 2 failure transfer, if activated,
will perform:
1. If OUT2 selects COOL, and BPLS is selected for O1FT, then output 2 will per-
form bumpless transfer. Thereafter, the previous averaging value of MV2 will be
used for controlling output 2.
2. If OUT2 selects COOL, and a value of 0 to 100.0% is set for O2FT, then output
2 will perform failure transfer. Thereafter, the value of O1FT will be used for
controlling output 2.
Alarm 1 failure transfer is activated as the controller enters failure mode.
Thereafter, alarm 1 will transfer to the ON or OFF state preset by A1FT.
Exception: If A1FN is configured for loop break (LB) alarm or sensor break
(SENB) alarm, alarm 1 will be switched to ON state independent of the setting of
A1FT. If A1FN is configured for dwell timer (TIMR), alarm 1 will not perform
failure transfer.
Alarm 2 failure transfer is activated as the controller enters failure mode.
Thereafter, alarm 2 will transfer to the ON or OFF state preset by A2FT.
Exception: If A2FN is configured for loop break (LB) alarm or sensor break
(SENB) alarm, alarm 2 will be switched to ON state independent of the setting of
A2FT. If A2FN is configured for dwell timer (TIMR), alarm 2 will not perform
failure transfer.
Failure mode occurs as:
1. SB1E
2. SB2E
3. ADER
Failure Transfer of output
1 and output 2 occurs as:
1. Power start (within 2.5 seconds)
2. Failure mode is activated
3. Manual mode is activated
4. Calibration mode is activated
Failure Transfer of alarm 1
and alarm 2 occurs as:
Failure mode is activated
Failure Transfer Setup:
1. O1FT
2. O2FT
3. A1FT
4. A2FT
- Instruction Manual 1
- TEC-9300 1
- Self-Tune Fuzzy / PID Process 1
- Temperature Controller 1
- Chapter 1 Overview 5
- Related Products 6
- 1–2 Ordering Code 6
- Figure 1. Access Hole 7
- Overview 7
- Table 1.1 DIP Switch 7
- Configuration 7
- 1–4 Keys and Displays 8
- 1–6 System Modes 11
- 1–7 Parameter Description 12
- Chapter 2 Installation 19
- 2–6 Thermocouple Input Wiring 20
- 2–4 Power Wiring 20
- 2–7 RTD Input Wiring 21
- 2–8 Linear DC Input Wiring 21
- 2–10 Event Input wiring 23
- 2–11 Output 1 Wiring 24
- 2–12 Output 2 Wiring 25
- Figure 2.19 RS-232 Wiring 28
- 3–1 Input 1 29
- 3–2 OUT1 and OUT2 Types 30
- 3–3 Configuring User Menu 30
- 3–4 Heat Only Control 30
- 3–5 Cool Only Control 31
- 3–6 Heat-Cool Control 32
- 3–7 Dwell Timer 33
- 3–8 Process Alarms 34
- 3–9 Deviation Alarm 35
- 3–10 Deviation Band Alarm 36
- 3–11 Heater Break Alarm 37
- 3–12 Loop Break Alarm 37
- 3–13 Sensor Break Alarm 38
- 3–14 SP1 Range 38
- 3–15 PV1 Shift 38
- 3–16 Failure Transfer 39
- 3–17 Bumpless Transfer 40
- 3–18 Self tuning 40
- Self-tune Menu 40
- 3–19 Auto tuning 41
- 3–20 Manual Tuning 42
- 3–21 Signal Conditioner 43
- DC Power Supply 43
- 3–22 Manual Control 43
- 3–23 Display Mode 44
- 3–25 Reload Default Values 44
- 4–1 Event Input 45
- 4–2 Second Set Point 45
- 4–3 Second PID Set 46
- 4–4 Ramp and Dwell 46
- 4–5 Remote Set Point 47
- 4–6 Differential Control 47
- 4–7 Output Power Limits 48
- 4–8 Data Communication 48
- 4–9 Analog Retransmission 49
- 4–10 Digital Filter 49
- 4–11 Sleep Mode 49
- 4–12 Pump Control 50
- 4–13 Remote Lockout 50
- Chapter 5 Applications 51
- 5–3 Heat Only Control 52
- 5–5 Heat-Cool Control 53
- 5–4 Cool Only Control 53
- 5–6 Ramp and Dwell 54
- 5–7 Remote Set 55
- 5–8 Differential Control 55
- 5–9 Dual Set Point/PID 56
- 5–10 RS-485 57
- 5–11 RS-232 58
- 5–12 Retransmit 58
- Chapter 6 Calibration 59
- Troubleshooting procedures: 61
- Chapter 8 Specifications 65
- PID: Fuzzy logic modified 66
- 9-1 Functions Supported 67
- 9-2 Exception Responses 68
- 9-3 Parameter Table 69
- P= 100.0 80
- 9-3 Communication Examples 80
- A–1 Menu Existence Conditions 81
- A–2 Factory Menu Description 84
- A–3 Glossary 85
- A–4 Memo 89
- A–5 Warranty 91
- TEMPCO’s Visionary Solutions 92
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.033 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais