Connect-Tek Transa PRO 17 Manual de Instruções Página 30
- Página / 92
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
26
3–2 OUT1 and OUT2 Types
O1TY: Selects the signal type for Output 1.
The selection should be consistent with the
output 1 module installed.
The available output 1 signal types are:
RELY: Mechanical relay
SSRD: Pulsed voltage output to drive SSR
SSR: Isolated zero-switching solid-state relay
4–20: 4–20mA linear current output
0–20: 0–20mA linear current output
0–1V: 0–1V linear voltage output
0–5V: 0–5V linear voltage output
1–5V: 1–5V linear voltage output
0–10V: 0–10V linear voltage output
O2TY:Selects the signal type for Output 2
The selection should be consistent with the
output 2 module installed.
The available output 2 signal types are the same as for
O1TY.
The range for linear current or voltage may not be very accurate.
For 0% output, the value for 4–20mA may be 3.8–4mA; while
for 100% output, the value for 4–20mA may be 20–21mA.
However, this deviation will not degrade the control perform-
ance at all.
3–3 Configuring User Menu
Most conventional controllers are designed with a fixed order in
which the parameters scroll. The TEC-9300 has the flexibility to
allow you to select those parameters which are most significant
to you and put these parameters at the front of the display
sequence.
SEL1: Selects the most significant parameter for
view and change.
SEL2: Selects the 2nd most significant parameter for
view and change.
SEL3: Selects the 3rd most significant parameter for
view and change.
SEL4: Selects the 4th most significant parameter for
view and change.
SEL5: Selects the 5th most significant parameter for
view and change.
Range: NONE, TIME, A1.SP, A1.DV,
A2.SP, A2.DV, RAMP, OFST, REFC, SHIF,
PB1, TI1, TD1, C.PB, DB, SP2, PB2, TI2,
TD2
When using the up and down keys to select the parameters, you
may not see all of the above parameters. The number of visible
parameters is dependent on the setup condition. The hidden
parameters for the specific application are also deleted from the
SEL selection.
Example:
A1FN selects TIMR
A2FN selects DE.HI
PB1=10
TI1=0
SEL1 selects TIME
SEL2 selects A2.DV
SEL3 selects OFST
SEL4 selects PB1
SEL5 selects NONE
Now, the upper display scrolling becomes:
3–4 Heat Only Control
Heat Only ON-OFF
Control: Select REVR for
OUT1, set PB1 to 0, SP1 is used
to adjust set point value, O1HY
is used to adjust dead band for
ON-OFF control, TIME is used
to adjust the dwell timer (enabled
by selecting TIMR for A1FN or A2FN). Output 1 hysteresis
(O1HY) is enabled in the case of PB1=0. The heat only on-off
control function is shown in the diagram at right:
Setup ON-OFF:
OUT1 =
PB1 = 0
Adjust: SP1, O1HY, TIME
(if enabled)
3–4 Heat Only Control continued next page…
- Instruction Manual 1
- TEC-9300 1
- Self-Tune Fuzzy / PID Process 1
- Temperature Controller 1
- Chapter 1 Overview 5
- Related Products 6
- 1–2 Ordering Code 6
- Figure 1. Access Hole 7
- Overview 7
- Table 1.1 DIP Switch 7
- Configuration 7
- 1–4 Keys and Displays 8
- 1–6 System Modes 11
- 1–7 Parameter Description 12
- Chapter 2 Installation 19
- 2–6 Thermocouple Input Wiring 20
- 2–4 Power Wiring 20
- 2–7 RTD Input Wiring 21
- 2–8 Linear DC Input Wiring 21
- 2–10 Event Input wiring 23
- 2–11 Output 1 Wiring 24
- 2–12 Output 2 Wiring 25
- Figure 2.19 RS-232 Wiring 28
- 3–1 Input 1 29
- 3–2 OUT1 and OUT2 Types 30
- 3–3 Configuring User Menu 30
- 3–4 Heat Only Control 30
- 3–5 Cool Only Control 31
- 3–6 Heat-Cool Control 32
- 3–7 Dwell Timer 33
- 3–8 Process Alarms 34
- 3–9 Deviation Alarm 35
- 3–10 Deviation Band Alarm 36
- 3–11 Heater Break Alarm 37
- 3–12 Loop Break Alarm 37
- 3–13 Sensor Break Alarm 38
- 3–14 SP1 Range 38
- 3–15 PV1 Shift 38
- 3–16 Failure Transfer 39
- 3–17 Bumpless Transfer 40
- 3–18 Self tuning 40
- Self-tune Menu 40
- 3–19 Auto tuning 41
- 3–20 Manual Tuning 42
- 3–21 Signal Conditioner 43
- DC Power Supply 43
- 3–22 Manual Control 43
- 3–23 Display Mode 44
- 3–25 Reload Default Values 44
- 4–1 Event Input 45
- 4–2 Second Set Point 45
- 4–3 Second PID Set 46
- 4–4 Ramp and Dwell 46
- 4–5 Remote Set Point 47
- 4–6 Differential Control 47
- 4–7 Output Power Limits 48
- 4–8 Data Communication 48
- 4–9 Analog Retransmission 49
- 4–10 Digital Filter 49
- 4–11 Sleep Mode 49
- 4–12 Pump Control 50
- 4–13 Remote Lockout 50
- Chapter 5 Applications 51
- 5–3 Heat Only Control 52
- 5–5 Heat-Cool Control 53
- 5–4 Cool Only Control 53
- 5–6 Ramp and Dwell 54
- 5–7 Remote Set 55
- 5–8 Differential Control 55
- 5–9 Dual Set Point/PID 56
- 5–10 RS-485 57
- 5–11 RS-232 58
- 5–12 Retransmit 58
- Chapter 6 Calibration 59
- Troubleshooting procedures: 61
- Chapter 8 Specifications 65
- PID: Fuzzy logic modified 66
- 9-1 Functions Supported 67
- 9-2 Exception Responses 68
- 9-3 Parameter Table 69
- P= 100.0 80
- 9-3 Communication Examples 80
- A–1 Menu Existence Conditions 81
- A–2 Factory Menu Description 84
- A–3 Glossary 85
- A–4 Memo 89
- A–5 Warranty 91
- TEMPCO’s Visionary Solutions 92
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais