Connect-Tek USB-2 Especificações

xxMSO2000B, DPO2000B, MSO2000 and DPO2000Series OscilloscopesZZZProgrammer Manual*P077073800*077-0738-00

Getting StartedTable 1-2: USB Device ParametersParameter ValueManufacturerID0x0699 (decimal 1689)Product ID0x399 DPO2002B (decimal 921)0x39A MSO2002B

Commands Listed in Alphabetical OrderConditionsThis command requires a DPO2COMP application module.GroupBusSyntaxBUS:B<x>:RS232C:DISplaymo de {F

Commands Listed in Alphabetical OrderSyntaxBUS:B<x>:RS232C:POLarity {NORMal|INVERTed}BUS:B<x>:RS232C:POLarity?ArgumentsNORMal sets the RS2

Commands Listed in Alphabetical OrderBUS:B<x>:SPI:BITOrderSets or returns the bit order for the specified SPI bus.ConditionsThis command requires

Commands Listed in Alphabetical OrderGroupBusSyntaxBUS:B<x>:SPI{:CLOCK|:SCLK} :SOUrce {CH1|CH2|CH3|CH4|D0|D1|D2|D3|D4|D5|D6|D7|D8 |D9|D10|D11|D1

Commands Listed in Alphabetical OrderArgumentsCH1-CH4 is the channel to use as the SPI MISO source.D0-D15 is the digital channel to use as the SPI MIS

Commands Listed in Alphabetical OrderConditionsThis command requires a DPO2EMBD application module.GroupBusSyntaxBUS:B<x>:SPI:DATA:SIZe <NR1&

Commands Listed in Alphabetical OrderGroupBusSyntaxBUS:B<x>:SPI:IDLETime <NR3>BUS:B<x>:SPI:IDLETime?Arguments<NR3> specifies th

Commands Listed in Alphabetical OrderArgumentsCH1–CH4 is the channel to use as the SPI SS source.D0–D15 is the digital channel to use as the SPI SS so

Commands Listed in Alphabetical OrderBUS:LOWerthreshold:CH<x>Sets the lower threshold for each channel. This applies to all searchand trigger ty

Commands Listed in Alphabetical OrderArgumentsECL specifies a presetECL high level of –1.3 V.TTL specifies a TTL preset high level of 1.4 V.<NR3>

Getting Started1. Use the optional5VDCpower adapter connected to the 5 VDCpower inputon the Adapter.2. Use an appropriate USB cable connected to a pow

Commands Listed in Alphabetical OrderArguments<NR3> specifiesthe threshold in volts.ECL specifies a preset ECL high level of –1.3 V.TTL specifies a

Commands Listed in Alphabetical Order*CAL? (Query Only)Performs an internal self-calibration and returns the oscilloscope calibration status.NOTE. Dis

Commands Listed in Alphabetical OrderCALibrate:FACtory:STATus? (Query Only)Returns the factory calibration status value saved in nonvolatile memory.Gr

Commands Listed in Alphabetical OrderCALibrate:INTERNal:STATus? (Query Only)Returns the current status of the oscilloscope internal signal path calibr

Commands Listed in Alphabetical OrderCALibrate:RESults:FACtory? (Query Only)Returns the status of internal and factory calibration, without performing

Commands Listed in Alphabetical OrderCH<x>? (QueryOnly)Returns the vertical parameters for channel <x>, where x is the channel number.Grou

Commands Listed in Alphabetical OrderArgumentsAC sets channel<x> to AC coupling.DC sets channel <x> to DC coupling.GND sets channel<x&g

Commands Listed in Alphabetical OrderSyntaxCH<x>:IMPedanceCH<x>:IMPedance?CH<x>:INVertSets or returns the invert function for channe

Commands Listed in Alphabetical OrderCH<x>:OFFSetSets or returns the vertical offset for channel <x>, where x is the channel number.This c

Commands Listed in Alphabetical Orderif the positionfor Channel 3 is set to 2.0 and the offset is set to 3.0, then inputsignals equal to 3.0 units are

Getting StartedNOTE. The CD that your oscilloscope shipped with contains additional tools forefficient connectivity between your oscilloscope and your

Commands Listed in Alphabetical OrderArgumentsExecute auto zeros the probe.CH<x>:PRObe:COMMAND (No Query Form)Sets the state of the p robe contr

Commands Listed in Alphabetical OrderNOTE. This command will returnPASSEDfor probes that do not support degaussoperations.GroupVerticalSyntaxCH<x&g

Commands Listed in Alphabetical OrderGroupVerticalSyntaxCH<x>:PRObe:GAIN <NR3>CH<x>:PRObe:GAIN?Related CommandsCH<x>:SCAleArgu

Commands Listed in Alphabetical OrderExamplesCH1:PROBE:ID:SERNUMBER?might return :CH1:PROBE:ID:SERNUMBER"B010289"indicating that the serial

Commands Listed in Alphabetical OrderGroupVerticalSyntaxCH<x>:PRObe:SIGnal {BYPass|PASS}CH<x>:PRObe:SIGnal?ArgumentsBYPass sets the probe

Commands Listed in Alphabetical OrderSyntaxCH<x>:SCAle <NR3>CH<x>:SCAle?Related CommandsCH<x>:OFFSet, CH<x>:POSition, RE

Commands Listed in Alphabetical OrderCH<x>:YUNitsSets or returns the units for the channel specified by <x>, where x is the channelnumber.

Commands Listed in Alphabetical Order*CLS can s uppress a Service Request that is to be generated by an * OPC. Thiswill happen if a single sequence ac

Commands Listed in Alphabetical OrderArgumentsOFF removes thecursors from the display but does not change the cursor type.SCREEN specifies both horizon

Commands Listed in Alphabetical OrderRelated CommandsCURSor:HBArs:UNItsReturnsA floating point value with an exponent.ExamplesCURSOR:HBARS:DELTA? might

Getting Started1. Install the Tektronix OpenChoice Desktop software package, either from theCD that came with your instrument or from the Tektronix we

Commands Listed in Alphabetical OrderArgumentsBASe selects the vertical units for the selected waveform.PERcent selects ratio cursors.ExamplesCURSOR:H

Commands Listed in Alphabetical OrderSyntaxCURSor:MODe {TRACk|INDependent}CURSor:MODe?ArgumentsTRACk ties the navigational functionality of the two cu

Commands Listed in Alphabetical OrderCURSor:VBArs:DELTa? (Query Only)Returns the horizontal difference between the two v ertical bar cursors. The unit

Commands Listed in Alphabetical OrderCURSor:VBArs:POSITIO N<x>Sets or returns the horizontal position for the specified vertical bar cursor. Thec

Commands Listed in Alphabetical OrderReturnsSECONDS, HERTZ, DEGREES,orPERCENT, depending on the current vertical barcursor units.ExamplesCURSOR:VBARS:

Commands Listed in Alphabetical OrderSyntaxCURSor:VBArs:VDELTa?Related CommandsCURSor:HBArs:UNItsReturns<NR3> indicates the horizontal differenc

Commands Listed in Alphabetical OrderCURSor:XY:POLar:THETA:DELta? (Query Only)Returns the XY cursor polar angle delta.GroupCursorSyntaxCURSor:XY:POLar

Commands Listed in Alphabetical OrderCURSor:XY:PRODUCT:POSITION<x>? (Query Only)Returns the position of the X or Y cursor used to calculate the

Commands Listed in Alphabetical OrderCURSor:XY:RATIO:UNIts? (Query Only)Returns the cursor X and cursor Y units for the ratio measurement.GroupCursorS

Commands Listed in Alphabetical OrderCURSor:XY:RECTangular:Y:DELta? (Query Only)Returns The cursor Y delta value in rectangular coordinates.GroupCurso

Getting StartedTo set up e*Scope communications between your oscilloscope and a n etworkedcomputer:1. With the DPO2CONN Connectivity Module installed,

Commands Listed in Alphabetical Orderpreview parameters. The user should always follow acquisition parameter changeswith a single sequence OPC command

Commands Listed in Alphabetical Order<data> is the curve data.<newline> is a single byte new line character at the end of the data.<asc

Commands Listed in Alphabetical OrderExamplesDATA? might return:DATA:DESTINATION REF1:ENCDG RIBINARY;SOURCECH1;START 1;STOP 500;WIDTH 1DATA INIT initi

Commands Listed in Alphabetical OrderSyntaxDATa:COMPosition:AVAILable?ReturnsCOMPOSITE_YT for sample data.COMPOSITE_ENV for envelope or peak-detect da

Commands Listed in Alphabetical OrderGroupWaveform TransferSyntaxDATa:ENCdg{ASCIi|FAStest|RIBinary|R PBinary|SRIbinary|SRPbinary}DATa:ENCdg?Related Co

Commands Listed in Alphabetical OrderExamplesDATA:ENCDG? might return:DATa:ENCDG SRPBINARY for the format of theoutgoing w aveform data .DATA:ENCDG RP

Commands Listed in Alphabetical OrderGroupWaveform TransferSyntaxDATa:SOUrce {CH1|CH2|CH3|CH4|MATH|REF1 |REF2|D0|D1|D2|D3|D4|D5|D6|D7|D 8|D9|D10|D11|D

Commands Listed in Alphabetical OrderExamplesDATA:SOURCE? might return :DATA:SOURC E REF2 indicating that the source forthe waveform d ata which is tr

Commands Listed in Alphabetical OrderGroupWaveform TransferSyntaxDATa:STARt <NR1>DATa:STARt?Related CommandsCURVe, DATa, DATa:STOP, WFMInpre:NR_

Commands Listed in Alphabetical OrderArguments<NR1> is the last data point that will be transferred, which ranges from 1 tothe record length. If

Getting Started4. On the menu bar of your PC’s web browser, type in the oscilloscope’sInstrument IP address and press Enter.5. You should now see the

Commands Listed in Alphabetical OrderSyntaxDATE <Q String>DATE?Related CommandsTIMEArguments<QString> is a date in the form "yyyy-mm-

Commands Listed in Alphabetical OrderDESESets or returns the bits in the Device Event Status Enable Register (DESER). TheDESER is the mask that determ

Commands Listed in Alphabetical OrderArgumentsALWAYS continues looping until the self tests (diagnostics) are stopped via thefront panel or by an osci

Commands Listed in Alphabetical OrderDIAg:RESUlt:FLAg? (Query Only)Returns the pass/fail status from the last self-test sequence exec ution. U se this

Commands Listed in Alphabetical OrderDIAg:SELect (No Query Form)Sets the type of diagnostics grouping.GroupCalibration a nd DiagnosticSyntaxDIAg:SELec

Commands Listed in Alphabetical OrderExamplesDIAG:SELECT:CPUsets the oscilloscope to run just CPU tests.DIAg:STATE (No Query Form)This command starts

Commands Listed in Alphabetical OrderRelated CommandsDATE, TIMEArgumentsDATEOnly enables the display of date.TIMEOnly enables the display of time.DATE

Commands Listed in Alphabetical OrderSyntaxDISplay:FORMat {YT|XY}DISplay:FORMat?ArgumentsYT sets the display to a voltage versus time format and is th

Commands Listed in Alphabetical OrderSyntaxDISplay:GRAticule {CRO SSHair|FRAme|FUL l|GRId}DISplay:GRAticule?ArgumentsCROSSHair specifies a frame and cr

Commands Listed in Alphabetical OrderDISplay:INTENSITy:GLITchSets the intensity of the glitch capture background of the waveform display. Theintensity

Getting Started1-10 MSO2000B, DPO2000B, MSO2000 and DPO2000 Series Oscilloscopes Programmer Manual

Commands Listed in Alphabetical OrderGroupDisplaySyntaxDISplay:INTENSITy:WAVEfor m <NR1>DISplay:INTENSITy:WAVEfor m?Arguments<NR1> is the

Commands Listed in Alphabetical OrderMINImum specifies that the waveform persistence is set to the minimum valueof 0.0E0.ExamplesDISPLAY:PERSISTENCE 3s

Commands Listed in Alphabetical OrderGroupMSOSyntaxD<x>:POSition <NR3>D<x>:POSition?Arguments<NR3> is the position of the digi

Commands Listed in Alphabetical OrderRelated Commands*CLS, DESE, *ESR?, EVENT?, EVMsg?, *SRE, *STB?Arguments<NR1> specifies the binary bits of th

Commands Listed in Alphabetical OrderSyntaxETHERnet:DHCPbootp {ON |OFF}ETHERnet:DHCPbootp?ArgumentsON enables the oscilloscope t o search the network

Commands Listed in Alphabetical OrderArguments<QString> is the network domain name, enclosed in quotes.ExamplesETHERNET:DOMAINNAME “Alpha1.Mycor

Commands Listed in Alphabetical OrderSyntaxETHERnet:HTTPPort <QSt ring>ETHERnet:HTTPPort?Arguments<QString> is an integer port number, enc

Commands Listed in Alphabetical OrderExamplesETHERNET:NAME“labscope1” sets the oscilloscope's network name.ETHERnet:PASSWordSets or returns the H

Commands Listed in Alphabetical OrderReturnsOK is returned if the computer at the gateway IP address answers.NORESPOnsE is returned if the computer at

Commands Listed in Alphabetical OrderEVMsg? (QueryOnly)Removes a single event code from the Event Queue that is associated with theresults of the last

Command SyntaxYou can control the operations and functions of the oscilloscope through theEthernet port or the USB 2.0 device port using commands and

Commands Listed in Alphabetical OrderFACtory (No Query Form)Resets the oscilloscope to its factory default settings.This command does the following:Cl

Commands Listed in Alphabetical OrderFILESystemReturns the directory listing of the current working directory and the number ofbytes of free space ava

Commands Listed in Alphabetical OrderSyntaxFILESystem:CWD {<new working directory p ath>}Arguments<new wo rking directory path> is a quote

Commands Listed in Alphabetical OrderGroupFile SystemSyntaxFILESystem:DIR?Related CommandsFILESystem:CWD, FILESystem:MKDirArgumentsNoneReturnsFILESyst

Commands Listed in Alphabetical OrderGroupFile SystemSyntaxFILESystem:FREESpace?Related CommandsFILESystem:FREESpace?, FILESystem:CWDFILESystem:MKDir

Commands Listed in Alphabetical OrderRelated CommandsFILESystem:CWDArguments<QString> is a quoted string that defines the file name and path. If t

Commands Listed in Alphabetical OrderRelated CommandsFILESystem:CWDArguments<directory path> is a quoted s tr ing that defines the directory name

Commands Listed in Alphabetical OrderArguments<NR3> is the integer format for the current FilterVu frequency setting.ExamplesFILTERVU:FREQUENCY?

Commands Listed in Alphabetical OrderTable 2-37: FPAnel:PRESS argumentsArgument DescriptionACQuireAcquire buttonSAVERecall Save/RecallMenu buttonMEASu

Commands Listed in Alphabetical OrderTable 2-37: FPAnel:PRESS arguments (cont.)Argument DescriptionBMENU5Screen bottom menu buttonBMENU6Screen bottom

Command SyntaxTable 2-2: Command Message ElementsSymbol Meaning<Header>This is the basic command name. If the header ends with a questionmark, t

Commands Listed in Alphabetical Orderclockwise rotation. The magnitude of <n> specifies the amount of the turn, where<n> = 1 represents tur

Commands Listed in Alphabetical OrderRelated Commands*WAI, *CLSArgumentsSTART sends a block of data representing the current screen image to the reque

Commands Listed in Alphabetical OrderArgumentsON or <NR1> ≠ 0turns preview mode on.OFF or <NR1> = 0 turns preview mode off.HEADerSets or r

Commands Listed in Alphabetical OrderSyntaxHORizontal?ExamplesHORIZONTAL? might return the following horizontalsettings:HORIZONTAL:DIGITAL:RECOR DLENG

Commands Listed in Alphabetical Order<NR1> = 0 sets the Horizontal Delay Mode to off; any other value sets this modeto on.ExamplesHORIZONTAL:DEL

Commands Listed in Alphabetical OrderSyntaxHORizontal:DIGital:SAMPLERate:MAIN?HORizontal:POSitionSets or returns the horizontal position. If Horizonta

Commands Listed in Alphabetical OrderGroupHorizontalSyntaxHORizontal:RECOrdlength <NR1>HORizontal:RECOrdlength?Arguments<NR1> represents t

Commands Listed in Alphabetical OrderGroupHorizontalSyntaxHORizontal:SCAle <NR3>HORizontal:SCAle?Arguments<NR3> specifies the range from 2

Commands Listed in Alphabetical Order*IDN? (Query Only)Returns the oscilloscope identification code.GroupMiscellaneousSyntax*IDN?Related CommandsID?Exa

Commands Listed in Alphabetical OrderGroupMiscellaneousSyntaxLOCk {A LL|NONe}LOCk?Related CommandsUNLockArgumentsALL disables all front-panel controls

Command SyntaxQueriesQueries cause the oscilloscope to return status or setting information. Querieshave the structure:[:]<Header>[:]<Header&

Commands Listed in Alphabetical OrderINTERNAL;:SAVE:ASSIGN:TYPE SETUP;:TRIGGER:A:MODEAUTO;TYPE EDGE;LE V EL 20.0000E-3;LEVEL:CH120.0000E-3;CH2 0.0000;

Commands Listed in Alphabetical OrderSyntaxMARK:CREATE {CH<x>|MATH|B<x>|REF<x>|COLUM N|DIGItal}ArgumentsCH<x> creates the mark

Commands Listed in Alphabetical OrderMARK:SELected:END? (Query Only)Returns the end of the selected mark, 0 to 100% of the waveform.GroupMarkSyntaxMAR

Commands Listed in Alphabetical OrderMARK:SELected:SOURCE? (Query Only)Returns the source waveform for the selected mark.GroupMarkSyntaxMARK:SELected:

Commands Listed in Alphabetical OrderMARK:TOTal? (Query Only)Returns how many marks are currently in use.GroupMarkSyntaxMARK:TOTal?MATH[1]:LABelSets o

Commands Listed in Alphabetical Order"V";:MATH:HORIZONTAL:SCALE 4.0000E-6;POSITION 50.0000;UNITS"s";:MATH:SPECTRAL:MAG DB;WINDOW H

Commands Listed in Alphabetical OrderExamplesMATH1:DEFINE "CH1+CH2"adds the Ch 1 waveform and Ch 2 waveform,storing the results in Math 1.MA

Commands Listed in Alphabetical OrderMATH[1]:HORizontal:UNItsReturns the math waveform horizontal measurement unit value.GroupMathSyntaxMATH[1]:HORizo

Commands Listed in Alphabetical OrderReturnsA value between0 and 1, which represents the fractional portion of the sourcerecord.MATH[1]:SPECTral:GATin

Commands Listed in Alphabetical OrderSyntaxMATH[1]:SPECTral:NYQUISTFreq?MATH[1]:SPECTral:WINdowSets or returns the window function for the spectral an

Command SyntaxClearing the oscilloscopeYou can clear the Output Queue and reset the oscilloscope to accept a newcommand or query by using the selected

Commands Listed in Alphabetical OrderRelated CommandsMATH[1]:DEFineArgumentsDUAL sets the math waveform mode to dual waveform math.FFT sets the math w

Commands Listed in Alphabetical OrderRelated CommandsCH<x>:SCAle, REF<x>:VERTical:SCAleArguments<NR3> is the scale-per-division in t

Commands Listed in Alphabetical OrderDELAY:DIRECTION FORWAR DS;EDGE1 RISE;EDGE2RISE;:MEASUREMENT:MEAS3:S TATE 1;TYPE PK2PK;UNITS "V";SOURCE1

Commands Listed in Alphabetical OrderCURSor limits measurements to the portion of the waveform between the verticalbar cursors, even if they are off s

Commands Listed in Alphabetical OrderMEASUrement:IMMed:DELay:DIRectionSets or returns the starting point and direction that determines the delay "

Commands Listed in Alphabetical OrderRelated CommandsMEASUrement:IMMed:SOUrce1MEASUrement:IMMed:SOUrce2Arguments<x> specifies which waveform to u

Commands Listed in Alphabetical OrderExamplesMEASUREMENT:IMMED:SOURCE1 MATH1specifies Math1 as t he immediate measurement source.MEASUREMENT:IMMED:SOUR

Commands Listed in Alphabetical OrderFor SOUrce2: Sets or returns the waveform to measure "to" when taking a delaymeasurement or phase measu

Commands Listed in Alphabetical OrderCMEan (cycle mean) measures the a rithmetic mean over the first cycle in thewaveform or the first cycle in the gate

Commands Listed in Alphabetical OrderNWIdth (negative width) measurement is the distance (time) between the middlereference (default = 50%) amplitude

Command SyntaxWhen concatenating commands and queries, you must follow these rules:1. Separate completely different headers by a semicolon and by the

Commands Listed in Alphabetical OrderVOLTS, VOLTS SQUARED, SEC, HERTZ, PERCENT, DIVS, SAMPLES,OHMS, AMPS, WATTS, MINUTES, DEGREES, UNKNOWN, AMPSSQUARE

Commands Listed in Alphabetical OrderMEASUrement:INDICators? (Query Only)Returns all measurement indicator parameters.GroupMeasurementSyntaxMEASUremen

Commands Listed in Alphabetical Order2 horizontal lines drawn on the graticule. The indicators show where themeasurement specified by MEASUrement:INDIC

Commands Listed in Alphabetical OrderMEASUrement:INDICators:VERT<x>? (Query Only)Returns the value of the specified vertical measurement indicato

Commands Listed in Alphabetical OrderMEASUrement:MEAS<x>:DELay? (Query Only)Returns the delay measurement parameters for the measurement specifie

Commands Listed in Alphabetical OrderMEASUREMENT:MEAS3:DELAY:DIRECTION?might return:MEASUREMENT:MEAS3:DELAY:D IRECTION BACKWARDS indicatingthat the cu

Commands Listed in Alphabetical OrderMEASUrement:MEAS<x>:MEAN? (Query Only)Returns the mean value accumulated for this measurement since the las

Commands Listed in Alphabetical OrderExamplesMEASUREMENT:MEAS2:SOURCE1 MATH1specifies Math 1 as the measurement2 source.MEASUREMENT:MEAS1:SOURCE1?might

Commands Listed in Alphabetical OrderFor SOUrce2: Sets or returns the waveform to measure "to" when taking a delaymeasurement or phase measu

Commands Listed in Alphabetical OrderMEASUREMENT:MEAS1:STATE?might return : MEASUREMENT:MEA S1:STATE 0indicating that measurement defined for measureme

Command SyntaxTable 2-4: End of Message TerminatorSymbol Meaning<EOM>Message terminatorThe end-of-message terminator must be the END message (EO

Commands Listed in Alphabetical OrderCARea (cycle area) measures the voltage over time. In other words, it measures, involt-seconds, the area over the

Commands Listed in Alphabetical OrderNOVershoot (negative overshoot) finds the negative overshoot value over theentire waveform or gated region. This m

Commands Listed in Alphabetical OrderMEASUREMENT:MEAS1:TYPE?might return :MEASUREMENT:MEAS 1:TYPE RMSindicating that measurement 1 is defined to measur

Commands Listed in Alphabetical OrderMEASUrement:METHodSets or returns the method used to calculate the 0% and 1 00% reference level.GroupMeasurementS

Commands Listed in Alphabetical OrderMEASUrement:REFLevel:ABSolute:HIGHSets or returns the high reference level, and is the upper reference level when

Commands Listed in Alphabetical OrderRelated CommandsMEASUrement:REFLevel:METHod, MEASUrement:IMMed:TYPe,MEASUrement:MEAS<x>:TYPeArguments<NR

Commands Listed in Alphabetical OrderMEASUrement:REFLevel:ABSolute:MID2Sets or returns the mid reference level for the "to" waveform whentak

Commands Listed in Alphabetical OrderMEASUrement:REFLevel:METHodSpecifies or returns the reference level units used for measurement calculations.NOTE.

Commands Listed in Alphabetical OrderSyntaxMEASUrement:REFLevel:PERCent:HIGH <NR3>MEASUrement:REFLevel:PERC ent:HIGH?Related CommandsMEASUrement

Commands Listed in Alphabetical OrderMEASUREMENT:REFLEVEL:PERCENT:LOW?might return:MEASUREMENT:REFLEVEL:PERC ENT:LOW 10 indicating that thepercentage

Command SyntaxMeasurement SpecifierMnemonicsCommands can specify whic h measurement to set or query as a mnemonic in theheader. Up to four automated me

Commands Listed in Alphabetical OrderGroupMeasurementSyntaxMEASUrement:REFLevel:PERC ent:MID2 <NR3>MEASUrement:REFLevel:PERC ent:MID2?Related Co

Commands Listed in Alphabetical OrderMESSageThis command sets o r queries message parameters.GroupMiscellaneousSyntaxMESSageMESSage?ExamplesMESSAGE? m

Commands Listed in Alphabetical Ordercommand automatically sizes the box to fi t the message. All four values ar ereturned in a query.MESSage:CLEAR (No

Commands Listed in Alphabetical OrderThe message string itself is not altered. The entire message can be returned as aquery response regardless of wha

Commands Listed in Alphabetical OrderIndex 10 Tek blueIndex 11 Bright blueIndex 12UndefinedIndex 13 BlueIndex 14UndefinedIndex 15 Dark blueBit 4If set,

Commands Listed in Alphabetical OrderExamplesMESSage:SHOW “Hello World”displays “Hello world” in the upper left corner of the box (you can define the b

Commands Listed in Alphabetical OrderArguments<QString> is the new password, which can contain up to 16 characters.ExamplesNEWPASS "myp ass

Commands Listed in Alphabetical Order*OPC? might return 1 to indicate that all pending OPC operations are finished.PASSWord(No Query Form)Enables the *

Commands Listed in Alphabetical OrderExamplesPICTBRIDGE:DATEPRINT? might return PICTBRIDGE:DATEPRINT DEFLTindicating that the default setting of the p

Commands Listed in Alphabetical OrderPICTBridge:IMAGESizeSets or returns the image print size.GroupPictBridgeSyntaxPICTBridge:IMAGESize {DEFLT|IN2P5BY

Command SyntaxTable 2-11: Quoted String ArgumentSymbol Meaning<QString> Quoted string of AS CII textA quoted string can include any character de

Commands Listed in Alphabetical OrderPICTBridge:PAPERSizeSets the output print paper size.GroupPictBridgeSyntaxPICTBridge:PAPERSize{DEFLT|L|L2|HAGAKIP

Commands Listed in Alphabetical OrderB2 for a B2 papersize.B3 for a B3 paper size.B4 for a B4 paper size.B5 for a B5 paper size.B6 for a B6 paper size

Commands Listed in Alphabetical OrderPICTBridge:PRINTQualSets or returns the output print quality.GroupPictBridgeSyntaxPICTBridge:PRINTQual {DEFLT|NRM

Commands Listed in Alphabetical Ordervalue sets the power-on status clear flag to true, enabling the power-on status clearpreventing any SRQ assertion

Commands Listed in Alphabetical OrderArguments<NR1> is a valuein the range from 1 to 10, which specifies a saved setup storagelocation.Examples*R

Commands Listed in Alphabetical OrderGroupSave and RecallSyntaxRECAll:WAVEform <file path>,REF<x>Related CommandsSAVe:WAVEform, FILESystem

Commands Listed in Alphabetical OrderREF<x>:HORizontal:DELay:TIMeSets or returns the horizontal delay time for reference w aveform <x>, wh

Commands Listed in Alphabetical OrderSyntaxREF<x>:LABel <Qstring>REF<x>:LABel?Arguments<Qstring> is an a lpha-numeric string o

Commands Listed in Alphabetical OrderGroupVerticalSyntaxREF<x>:TIMe?ExamplesREF2:TIME? might return “16:54:05”.REF<x>:VERTical:POSitionSet

Commands Listed in Alphabetical OrderEach waveform has a vertical scale parameter. For a signal with constantamplitude, increasing the Scale causes th

Command SyntaxMSO2000B, DPO2000B, MSO2000 and DPO2000 Series Oscilloscopes Programmer Manual 2-9

Commands Listed in Alphabetical OrderExamplesREM "This is a comment"is a comment string that the oscilloscope willignore.*RST (No Query Form

Commands Listed in Alphabetical OrderRelated Commands*RCL, RECAll:SETUp, SAVe:SETUpArguments<NR1> specifies a location in which to save the state

Commands Listed in Alphabetical OrderSAVe:IMAGe (No Query Form)Saves a capture of the screen image into the specified file. Supported imageformats are P

Commands Listed in Alphabetical OrderSAVe:IMAGe:LAYoutSets or returns the layout to use for saved screen images.GroupSave and RecallSyntaxSAVe:IMAGe:L

Commands Listed in Alphabetical OrderSAVe:WAVEform(NoQueryForm)This command saves a specified waveform or all displayed waveforms (excludingserial bus

Commands Listed in Alphabetical Order:SAVE:WAVEFORM:FILEFORMAT SPREADSHEET; :SAVE:WAVEFORM ALL,"E:/test_folder/test1_all. csv"saves all disp

Commands Listed in Alphabetical OrderSAVe:WAVEform:GATIngSpecifies whether save waveform operations should save the entire waveform(NONe) or a specified

Commands Listed in Alphabetical OrderSAVE:WAVEFORM:SPREADSHEET:RESOLUTIONREDUc edsets the reducedresolution waveform to be saved to a CSV file.SEARCH?

Commands Listed in Alphabetical Order:SEARCH:SEARCH1:TRIGGER:A:BUS:B1:I2C:DATA :DIRECTION NOCARE;:SEARCH:SEARCH1:TRIGGER:A :BUS:B2:I2C:DATA:DIRECTION

Commands Listed in Alphabetical Order:SEARCH:SEARCH1:TRIGGER:A:BUS:B2:LIN:ERRT YPE SYNC;:SEARCH:SEARCH1:TRIGGER:A: BUS:B1:PARALLEL:VALUE"XXXXXXXX

Command Syntax2-10 MSO2000B, DPO2000B, MSO2000 and DPO2000 Series Oscilloscopes Programmer Manual

Commands Listed in Alphabetical OrderTHRESHOLD:CH10.0E+0;CH2 0.0E+0;CH3 0.0E+0;CH4 0.0E+0; MATH0.0E+0;REF1 0.0E+0;REF2 0.0E+0;:SEARCH:SEARCH1:STATE 0S

Commands Listed in Alphabetical OrderSyntaxSEARCH:SEARCH<x>:TOTAL?Returns<NR1> is the total number of matches.SEARCH:SEARCH<x>:TRIGg

Commands Listed in Alphabetical Order:SEARCH:SEARCH1:TRIGGER:A:BUS:B2:I2C:DATA :VALUE "XXXXXXXX";:SEARCH1:TRIGGER:A:BUS:B1 :I2C:DATA:SIZE 1;

Commands Listed in Alphabetical Order:SEARCH:SEARCH1:TRIGGER:A:BUS:B2:LIN:IDEN TIFIER:VALUE"XXXXXX";:SEARCH:SEARCH1:TRIGGER:A: BUS:B1:LIN:ER

Commands Listed in Alphabetical OrderConditionsThis command requires a DPO2AUTO application m odule.GroupSearchSyntaxSEARCH:SEARCH<x>:TRIGger: A

Commands Listed in Alphabetical OrderLESSEQual searches for bus data less than or equal to the value specified bySEARCH:SEARCH<x>:TRIGger:A:BUS:B

Commands Listed in Alphabetical OrderSEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:CAN:FRAMEtypeSets or returns the CAN Frame Type to be used if the

Commands Listed in Alphabetical OrderSEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:CAN{:IDentifier|:ADDRess}:VALueSets or returns the binary address

Commands Listed in Alphabetical OrderGroupSearchSyntaxSEARCH:SEARCH<x>:TRIGger: A:BUS:B<x>:I2C:ADDRess:TYPe{GENeralcall|STARtbyte|HS mode|

Commands Listed in Alphabetical OrderSyntaxSEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:I2C:C ONDition{STARt|STOP|REPEATstart|AC KMISS|ADDRess|DATA

Command GroupsThis manual lists the MSO/DPO2000B and MSO/DPO2000 series IEEE488.2commands in two ways. First, it presents them by functional groups. T

Commands Listed in Alphabetical OrderGroupSearchSyntaxSEARCH:SEARCH<x>:TRIGger: A:BUS:B<x>:I2C:DATa:SIZe <NR1>SEARCH:SEARCH<x>

Commands Listed in Alphabetical OrderIDANDDATA specifies to search on the identifier and the data.WAKEup specifies to search on wake up.SLEEP specifies to

Commands Listed in Alphabetical OrderSyntaxSEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:LIN:D ATa:QUALifier{LESSThan|MOREThan|EQUal| UNEQual|LESSEQ

Commands Listed in Alphabetical OrderSEARCH:SEARCH1:TRIGGER:A:BUS:B1:LIN:DATA: SIZE?might returnSEARCH:SEARCH1:TRIGGER:A:B US:B1:LIN:DATA:SIZE 1 indic

Commands Listed in Alphabetical OrderExamplesSEARCH:SEARCH1:TRIGGER:A:BUS:B1:LIN:ERRTY PE?might returnSEARCH:SEARCH1:TRIGGER:A: BUS:B1:LIN:ERRTYPE SYN

Commands Listed in Alphabetical OrderSEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:RS232C:CONDitionSets or returns the condition for a RS232 trigger

Commands Listed in Alphabetical OrderSEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:RS232C:RX:DATa:VALueSets or returns the binary data string for a

Commands Listed in Alphabetical OrderSyntaxSEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:RS232 C:TX:DATa:VALueSEARCH:SEARCH<x>:TRIGger:A :BUS:

Commands Listed in Alphabetical OrderSEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:SPI:DATa{:MOSI|:O UT}:VALueSets or returns the binary data string

Commands Listed in Alphabetical OrderGroupSearchSyntaxSEARCH:SEARCH<x>:TRIGger:A :BUS:SOUrce {B1|B2}SEARCH:SEARCH<x>:TRIGger:A :BUS:SOUrce

Command GroupsAlias CommandGroupUse the Alias commands to define new commands as a sequence of standardcommands. You may find this useful when repeatedl

Commands Listed in Alphabetical OrderSEARCH:SEARCH<x>:TRIGger:A:LEVelSets or returns the level for an edge trigger search to deter mine where to

Commands Listed in Alphabetical OrderSyntaxSEARCH:SEARCH<x>:TRIGger:A:LEVel:MATH {TTL|ECL}SEARCH:SEARCH<x>:TRIGger:A :LEVel:MATH?Arguments

Commands Listed in Alphabetical OrderGroupSearchSyntaxSEARCH:SEARCH<x>:TRIGger: A:LOGIc:INPut:CH<x> {HIGH |LOW|X}SEARCH:SEARCH<x>:TR

Commands Listed in Alphabetical OrderArgumentsCH<x> specifiesa channel input as the clock source, where <x> = 1, 2, 3, or 4.MATH specifies t

Commands Listed in Alphabetical OrderSEARCH:SEARCH<x>:TRIGger:A:LOGIc:INPut:REF<x>Sets or returns the Boolean logic criteria for a logic t

Commands Listed in Alphabetical OrderSyntaxSEARCH:SEARCH<x>:TRIGger:A:LOGIc:PATtern: INPut:D<x>{HIGH|LOW|X}SEARCH:SEARCH<x>:TRIGger:

Commands Listed in Alphabetical OrderSEARCH:SEARCH<x>:TRIGger:A:LOGIc:PATtern:WHEnSets or returns the condition for generating a logic pattern t

Commands Listed in Alphabetical OrderSEARCH:SEARCH<x>:TRIGger:A:LOGIc:PATtern:WHEn:MORELimitSets or returns the minimum time that the selected p

Commands Listed in Alphabetical OrderArgumentsTTL specifies a presetTTL high level of 1.4 V.ECL specifies a preset ECL high level of –1.3 V.<NR3>

Commands Listed in Alphabetical OrderSEARCH:SEARCH<x>:TRIGger:A:LOWerthreshold:MATHSets or returns the math waveform lower threshold to determin

Command GroupsBus Command GroupUse the Bus commands when working with serial bus measurements.Install the DPO2EMBD application module when working wit

Commands Listed in Alphabetical OrderGroupSearchSyntaxSEARCH:SEARCH<x>:TRIGger: A:PULSEWidth:POLarity{NEGative|POSitive}SEARCH:SEARCH<x>:T

Commands Listed in Alphabetical OrderMOREthan places a mark if the pulse width is more than the time set by theSEARCH:SEARCH<x>:TRIGger:A:PULSEW

Commands Listed in Alphabetical OrderSEARCH:SEARCH<x>:TRIGger:A:RUNT:SOUrceSets or returns the source setting for a runt trigger search to deter

Commands Listed in Alphabetical OrderSEARCH:SEARCH<x>:TRIGger:A:RUNT:WIDthSets or returns the width setting for a runt trigger search to determi

Commands Listed in Alphabetical OrderArgumentsCH1–CH4 specifies an input channel as the edge source.MATH specifies the math waveform as the search sourc

Commands Listed in Alphabetical OrderMATH specifies the math waveform as the search s ource.REF specifies the reference waveform as the search source.D0

Commands Listed in Alphabetical OrderGroupSearchSyntaxSEARCH:SEARCH<x>:TRIGger: A:SETHold:SETTime <NR3>SEARCH:SEARCH<x>:TRIGger: A:S

Commands Listed in Alphabetical OrderSEARCH:SEARCH<x>:TRIGger:A:SETHold:THReshold:REF<x>Sets or returns the trigger search setup and hold

Commands Listed in Alphabetical OrderArgumentsPOSitive specifies that a pulse edge must traverse from the lower (mostnegative) to higher (most positive

Commands Listed in Alphabetical OrderUNEQual sets the trigger to occur when the transitioning signal is not equal tothe set volts/second rate ±5%.SEAR

MSO2000B, DPO2000B, MSO2000 and DPO2000Series OscilloscopesZZZProgrammer ManualxxRevision Awww.tektronix.com077-0738-00

Command GroupsTable2-15:BusCommands(cont.)Commands DescriptionBUS:B<x>:POSition Sets or returns the position of the specifiedbus waveformBUS:B<

Commands Listed in Alphabetical OrderArgumentsTTL specifies a presetTTL high level of 1.4 V.ECL specifies a preset ECL high level of –1.3 V.SEARCH:SEARC

Commands Listed in Alphabetical OrderSyntaxSELect {ON|OFF}ArgumentsON turns the selected waveform display on.OFF turns the selected waveform display o

Commands Listed in Alphabetical OrderExamplesSELECT:CH2 ON turns the channel 2 waveform display on, and selects channel 2.SELECT:CH1? might return :SE

Commands Listed in Alphabetical OrderSyntaxSELect:D<x> {<NR1>|OFF|ON}SELect:D<x>?ArgumentsON turns on the display of the specified wa

Commands Listed in Alphabetical OrderSELect:REF<x>Turns on and off the display of the reference waveform <x>. The <x > variablerepre

Commands Listed in Alphabetical OrderRelated CommandsHEADer, *LRN?,VERBoseExamplesSET? returns a long response, part of which could be as follows: :SE

Commands Listed in Alphabetical OrderSETUP<x>:LABELSets or returns the setup label for the specified channel <x>.GroupSave and RecallSyntax

Commands Listed in Alphabetical OrderArguments<NR1> is a valuein the range from 0 through 255. The binary bits of the SRERare set according to t

Commands Listed in Alphabetical Order10000 : WFMINPRE:PT_FMT Y :WFMINPRE :XUNIT "s" :WFMINPRE:XINCR4.0000E-9 :WFMINPRE:XZERO 0.0000 :WFMINPR

Commands Listed in Alphabetical OrderSyntaxTIME <Q String>TIME?Related CommandsDATEArguments<QString> is a time in the form "hh:mm:ss

Command GroupsTable 2-15: Bus Commands (cont.)Commands DescriptionSEARCH:SEARCH<x>:TRIGger:A:BUS?Returns the serial search typeSEARCH:SEARCH<

Commands Listed in Alphabetical OrderTRIGger (No Query Form)Forces a trigger event to occur.GroupTriggerSyntaxTRIGger FORCeTRIGger?ArgumentsFORCe crea

Commands Listed in Alphabetical Order800.0000E-3;:TRIGGER:A:LOWERTHRESHOLD:CH1 20.0000E-3;C H20.0000;CH3 0.0000;CH4 0.0000;:TRIGGER:A:HOLDOFF:TI ME20.

Commands Listed in Alphabetical OrderSyntaxTRIGger:A:BUS{I2C|SPI|CAN|RS232}TRIGger:A:BUS?ArgumentsI2C specifies the Inter-IC bus.SPI specifies the Seria

Commands Listed in Alphabetical OrderTRIGger:A:BUS:B<x>:CAN:DATa:DIRectionSets or returns the CAN trigger data direction to be valid on a Read,

Commands Listed in Alphabetical OrderUNEQual sets the oscilloscope to trigger when the data is not equal to the qualifi ervalue.LESSEQual sets the osci

Commands Listed in Alphabetical OrderSyntaxTRIGger:A:BUS:B<x>:CAN:DATa:VALue <QString>TRIGger:A:BUS:B<x>:CAN:DAT a:VALue?Arguments&l

Commands Listed in Alphabetical OrderConditionsThis command requires a DPO2AUTO application m odule.GroupTriggerSyntaxTRIGger:A:BUS:B<x>:CAN{:I

Commands Listed in Alphabetical OrderSyntaxTRIGger:A:BUS:B<x>:I2C:ADDRess:MODe {ADDR7|ADDR10}TRIGger:A:BUS:B<x>:I2C:ADD Ress:MODe?Argument

Commands Listed in Alphabetical OrderSyntaxTRIGger:A:BUS:B<x>:I2C:ADDRess:VALue <QString>TRIGger:A:BUS:B<x>:I2C:AD DRess:VALue?Argum

Commands Listed in Alphabetical OrderTRIGger:A:BUS:B<x>:I2C:DATa:DIRectionSets or returns the I2C trigger type to be valid on a Read, Write, o r

Command GroupsCalibration and Diagnostic Command GroupThe Calibration and Diagnostic commands provide information about the currentstate of o scillosc

Commands Listed in Alphabetical OrderTRIGger:A:BUS:B<x>:I2C:DATa:VALueSets or returns the binary data string used for I2C triggering if the trig

Commands Listed in Alphabetical OrderExamplesTRIGGER:A:BUS:B1:LIN:CONDITION ERRORsets the LIN trigger conditionto error.TRIGGER:A:BUS:B1:LIN:CONDI TIO

Commands Listed in Alphabetical OrderArgumentsLESSThan sets the LIN data qualifier to less than.MOREThan sets the LIN data qualifier to greater than.EQU

Commands Listed in Alphabetical OrderConditionsThis command requires a DPO2AUTO application module.GroupBusSyntaxTRIGger:A:BUS:B<x>:LIN:DAT a:VA

Commands Listed in Alphabetical OrderTRIGger:A:BUS:B<x>:LIN:IDentifier:VALueSets or returns the binary address string used for LIN trigger if the

Commands Listed in Alphabetical OrderGroupTriggerSyntaxTRIGger:A:BUS:B<x>:RS232C: CONDition{RXSTArt|RXDATA|RXENDPacke t|RXPARity|TXSTArt|TXDATA|

Commands Listed in Alphabetical OrderGroupTriggerSyntaxTRIGger:A:BUS:B<x>:RS232C :RX:DATa:VALueTRIGger:A:BUS:B<x>:RS232C :RX:DATa:VALue?Ar

Commands Listed in Alphabetical OrderTRIGger:A:BUS:B<x>:SPI:CONDitionSets or returns the trigger condition for a SPI trigger. Applies t o bus &l

Commands Listed in Alphabetical OrderTRIGger:A:BUS:B<x>:SPI:DATa{:OUT|:MOSI}:VALueSets or returns the binary data string to be used for a SPI tr

Commands Listed in Alphabetical OrderSyntaxTRIGger:A:BUS:SOUrce {B 1|B2}TRIGger:A:BUS:SOUrce?ArgumentsB1 specifies the Bus 1 source.B2 specifies the Bus

Command GroupsCursor CommandGroupUse the commands in the Cursor Command Group to control the cursor displayand readout. You can use these commands to

Commands Listed in Alphabetical OrderNOISErej specifies noise-rejection coupling, which provides stable triggeringby increa sing the trigger hysteresis

Commands Listed in Alphabetical OrderRelated CommandsTRIGger:A:EDGE:SLOpe, TRIGger:A:EDGE:COUPlingArgumentsCH1–CH4 specifies an analog input channel as

Commands Listed in Alphabetical OrderArguments<NR3> specifi esthe holdoff time in seconds. The range is from 20 ns through 8.0 s.ExamplesTRIGGER:

Commands Listed in Alphabetical OrderExamplesTRIGGER:A:LEVEL:AUXIN E CLsets the auxiliary input trigger level to -1.3volts.TRIGGER:A:LEVEL:AUXIN?might

Commands Listed in Alphabetical OrderArgumentsECL specifies a presetECL high level of –1.3 V.TTL specifies a preset TT L high level of 1.4 V.<NR3>

Commands Listed in Alphabetical Order3,and4aremeton four-channel oscilloscopes. On two-channel oscilloscopes,only channel 1 and channel 2 are availabl

Commands Listed in Alphabetical OrderTRIGger:A:LOGIc:INPut? (Query Only)Returns the logic input values for all channels. If a clock channel is defined,

Commands Listed in Alphabetical OrderSyntaxTRIGger:A:LOGIc:INPut:CLOCk:EDGE {FALL|RISe|EITher}TRIGger:A:LOGIc:INPut:CLOC k:EDGE?ArgumentsRISe specifies

Commands Listed in Alphabetical OrderTRIGger:A:LOGIc:PATtern? (Query Only)Returns the conditions used for generating an A logic pattern trigger, with

Commands Listed in Alphabetical OrderGroupTriggerSyntaxTRIGger:A:LOGIc:PATtern:IN Put:D<x> {HIGH|LOW|X}TRIGger:A:LOGIc:PATtern:IN Put:D<x>

Command GroupsTable 2-17: Cursor Commands (cont.)CommandDescriptionCURSor:XY:POLar:RADIUS:POSITION<x>? Returns the polar radius of the specifiedc

Commands Listed in Alphabetical OrderTRIGger:A:LOGIc:PATtern:WHEn:LESSLimitSets or returns the maximum time that the selected pattern may be true and

Commands Listed in Alphabetical OrderTRIGger:A:LOGIc:THReshold:(CH<x>|D<x>)This command sets or queries the logic trigger threshold voltag

Commands Listed in Alphabetical OrderExamplesTRIGGER:A:LOWERTHRESHOLD:CH2 50E-3sets the lower limit threshold forCH2ofthepulserunttriggerto50mV.TRIGGE

Commands Listed in Alphabetical OrderTRIGGER:A:MODE?might return :TRIGGER :A:MODE NORMAL indicating that avalid trigger event must occur before a trig

Commands Listed in Alphabetical OrderExamplesTRIGGER:A:PULSE:CLASS WIDTHspecifies a width pulse for the A trigger.TRIGGER:A:PULSE:CLASS? might return :

Commands Listed in Alphabetical OrderGroupTriggerSyntaxTRIGger:A:PULSEWidth:SOUrc e {{CH1|CH2|CH3|CH4|D0|D1|D2|D3|D4|D5|D6|D7|D8 |D9|D10|D11|D12|D13|D

Commands Listed in Alphabetical OrderExamplesTRIGGER:A:PULSEWIDTH:WHEN LESST HANspecifies that the duration of the Apulse will fall within defined high

Commands Listed in Alphabetical OrderGroupTriggerSyntaxTRIGger:A:RUNT:POLarity {EITher|NEGati ve|POSitive}TRIGger:A:RUNT:POLarity?ArgumentsPOSitive in

Commands Listed in Alphabetical OrderGroupTriggerSyntaxTRIGger:A:RUNT:WHEn {LESSthan|MOREt han|EQual|UNEQu al|OCCURS}TRIGger:A:RUNT:WHEn?Related Comma

Commands Listed in Alphabetical OrderExamplesTRIGGER:A:RUNT:WIDTH 15E-6sets the minimum width of the pulse runttriggerto15µs.TRIGGER:A:RUNT:WIDTH?migh

Command GroupsTable 2-18: Display CommandsCommandDescriptionDISplay?Returns current display settingsDISplay:CLOCk Sets or returns the display of the d

Commands Listed in Alphabetical OrderGroupTriggerSyntaxTRIGger:A:SETHold:CLOCk:E DGE {FALL|RISe}TRIGger:A:SETHold:CLOCk:E DGE?ArgumentsFALL specifies p

Commands Listed in Alphabetical OrderGroupTriggerSyntaxTRIGger:A:SETHold:CLOCk:TH Reshold {<NR3>|TTL|ECL}TRIGger:A:SETHold:CLOCk:TH Reshold?Argu

Commands Listed in Alphabetical OrderSyntaxDPO Models:TRIGger:A:SETHold:DATa:SO Urce {CH1|CH2|CH3|CH4|D0|D1|D2|D3|D4|D5|D6|D7|D 8|D9|D10|D11|D12|D13|D

Commands Listed in Alphabetical OrderTRIGger:A:SETHold:HOLDTimeSets or returns the hold time for setup and hold violation triggering.GroupTriggerSynta

Commands Listed in Alphabetical OrderGroupTriggerSyntaxTRIGger:A:SETHold:THResho ld:CH<x> {<NR3>|ECL|TTL}TRIGger:A:SETHold:THResho ld:CH&l

Commands Listed in Alphabetical OrderGroupTriggerSyntaxTRIGger:A{:TRANsition|:RIS EFall}?Related CommandsTRIGger:A:UPPerthreshold:CH<x> , TRIGge

Commands Listed in Alphabetical OrderArgumentsPOSitive indicates that a pulse edge must trave rse from the lower (mostnegative) to higher (most positi

Commands Listed in Alphabetical OrderSyntaxTRIGger:A{:TRANsition|:RISEFall}:WHEn{SLOWer|FASTer|EQual|UNEQu al}TRIGger:A{:TRANsition|:RIS EFall}:WHEn?A

Commands Listed in Alphabetical OrderLOGic specifi esthat a trigger occurs when specified conditions are met and iscontrolledbytheTRIGger:A:LOGIc? comma

Commands Listed in Alphabetical OrderGroupTriggerSyntaxTRIGger:A:VIDeo?ExamplesTRIGGER:A:VIDEO? might return :TRIGGER:A:VIDEO:POLARITYPOSITIVE;SOURCE

Command GroupsTable 2-19: Ethernet Commands (cont.)CommandDescriptionETHERnet:HTTPPortSets or returns the remote interface HTTPport valueETHERnet:IPAD

Commands Listed in Alphabetical OrderRelated CommandsTRIGger:A:VIDeo{:SYNC|:FIELD}Arguments<NR1> argument is an integer that sets the video line

Commands Listed in Alphabetical OrderGroupTriggerSyntaxTRIGger:A:VIDeo:SOUrce {CH1|CH2|CH3|CH 4}TRIGger:A:VIDeo:SOUrce?ArgumentsCH1–CH4 specifies the i

Commands Listed in Alphabetical OrderGroupTriggerSyntaxTRIGger:A:VIDeo{:SYNC|:FI ELD}{ODD|EVEN|ALLFields|ALLLi nes|NUMERic}TRIGger:A:VIDeo{:SYNC|:FI E

Commands Listed in Alphabetical OrderExamplesTRIGGER:EXTERNAL:PROBE?might return :TRIGGER:EXTERNAL:PROBE1.0E1for a 10X probe.TRIGger:EXTernal:YUNIts?

Commands Listed in Alphabetical OrderAUTO indicatesthat the oscilloscope is in the automatic mode and acquires dataeven in the abs ence of a trigger.R

Commands Listed in Alphabetical OrderUSBDevice:CONFigureEnables or disables the rear USB port for use with Pictbridge printers.GroupPictBridgeSyntaxUS

Commands Listed in Alphabetical OrderUSBTMC:PRODUCTID:HEXadecimal? (Query Only)Returns the product ID of the USBTMC device in hexadecimal format.Group

Commands Listed in Alphabetical OrderGroupMiscSyntaxUSBTMC:VENDORID:HEXadecima l?ExamplesUSBTMC:VENDORID:HEXADECIMA L? might returnUSBTMC:VENDORID:HEX

Commands Listed in Alphabetical Order*WAI (No QueryForm)Prevents the o scilloscope from executing further commands or queries until allpending command

Commands Listed in Alphabetical Order“V”;YMULT 4.0000E-3;YOFF 0.0000;YZERO 0.0000;:CURVE2,1,4,2,4,3,0,3,3,3,3,3,3, 4,3,5,6,6,7,3WFMInpre? (Query Only)

Command GroupsNOTE. Using back slas h as a path separator may produce some unexpectedresults, depending on how your application treats escaped charact

Commands Listed in Alphabetical OrderWFMInpre:BN_FmtSets or returns the format of binary data for incoming waveforms.GroupWaveform TransferSyntaxWFMIn

Commands Listed in Alphabetical OrderWFMInpre:BYT_OrSets or returns which byte of binary waveform data is expected first for incomingwaveform data when

Commands Listed in Alphabetical OrderExamplesWFMINPRE:COMPOSITION?might return :WFMINPRE:COMPOSI TIONSINGULAR_YTindicating that the sample part of sin

Commands Listed in Alphabetical OrderExamplesWFMINPRE:FILTERFREQ?might return :WFMINPRE:FILTERF REQ 200000000indicating that the FilterVu frequency fo

Commands Listed in Alphabetical OrderArgumentsENV spec ifies that the waveform is transmitted in envelope mode as maximumand minimum point pairs. OnlyY

Commands Listed in Alphabetical OrderSyntaxWFMInpre:XINcr <NR3>WFMInpre:XINcr?Related CommandsWFMInpre:XUNit, WFMOutpre:XINcr?Arguments<NR3&g

Commands Listed in Alphabetical OrderWFMInpre:XZEroSets or returns the position value, in XUNits, of the first sample of the incomingwaveform.GroupWave

Commands Listed in Alphabetical OrderRelated CommandsDATa:DESTination, WFMInpre:BYT_Nr, WFMInpre:YUNitArguments<NR3> is the vertical scale facto

Commands Listed in Alphabetical OrderWFMINPRE:YOFF?might return :WFMINPRE: YOFF 25 indicating that the verticalposition of the incoming waveform in di

Commands Listed in Alphabetical OrderGroupWaveform TransferSyntaxWFMInpre:YZEro <NR3>WFMInpre:YZEro?Related CommandsWFMInpre:YUNit, WFMOutpre:YZ

Command GroupsTable 2-21: FilterVuCommands (cont.)CommandDescriptionFILTERVu:FREQuency Sets or queries the FilterVu frequencyFILTERVu:FREQuency:AVAILa

Commands Listed in Alphabetical Order4.0000E-9;XZERO - 20.0000E-6;PT_OFF 0;YUNIT “V”;YMULT15.6250E-6;YOFF :”6.4000E+3;YZERO 0.0000WFMOutpre:BIT_NrSets

Commands Listed in Alphabetical OrderArgumentsRI specifies signed integer data point representation.RP specifies positive integer data point representat

Commands Listed in Alphabetical OrderSyntaxWFMOutpre:BYT_Or {LSB| MSB}WFMOutpre:BYT_Or?Related CommandsWFMOutpre:ENCdg, WFMOutpre:BYT_NrArgumentsLSB s

Commands Listed in Alphabetical OrderSyntaxWFMOutpre:ENCdg {ASCii| BINary}WFMOutpre:ENCdg?Related CommandsDATa:ENCdg, WFMOutpre:BYT_Nr, WFMInpre:FILTE

Commands Listed in Alphabetical OrderGroupWaveform TransferSyntaxWFMOutpre:NR_Pt?Related CommandsCURVe, DATa, DATa:STARt, DATa:STOP, SAVe:WAVEform,SAV

Commands Listed in Alphabetical OrderRelated CommandsDATa:SOUrceArgumentsArguments are ignored.ExamplesWFMOUTPRE:PT_OFF? might return WFMOUTPRE:PT_OFF

Commands Listed in Alphabetical Ordertime out and an error will be generated if the waveform specified by DATa:SOUrceis not turned on.GroupWaveform Tra

Commands Listed in Alphabetical OrderWFMOutpre:XINcr? (Query O nly)Returns the horizontal point spacing in units of WFMOutpre:XUNit for thewaveform sp

Commands Listed in Alphabetical OrderGroupWaveform TransferSyntaxWFMOutpre:XZEro?Related CommandsDATa:SOUrce, WFMOutpre:XUNit?ExamplesWFMOUTPRE:XZERO?

Commands Listed in Alphabetical OrderSyntaxWFMOutpre:YOFf?Related CommandsDATa:SOUrce, WFMOutpre:BYT_NrExamplesWFMOUTPRE:YOFF? might return :WFMOUTP R

Command GroupsHorizontal Command GroupUse the commands in the Horizontal Command Group to control the oscilloscopetime bases. You can set the time-per

Commands Listed in Alphabetical OrderExamplesWFMOUTPRE:YZERO?might return :WFMOUTPRE:YZERO -100.0000E-3indicating that vertical offset is set to –100

Commands Listed in Alphabetical OrderZOOm:ZOOM1? (Query Only)Returns the current horizontal positioning and scaling of the display.GroupZoomSyntaxZOOm

Commands Listed in Alphabetical OrderZOOM:ZOOM1:HORIZONTAL:POSITION?might return:ZOOM1:HORIZONTAL:POSITIO N 50.0000 indicating that the Zoom1reference

Commands Listed in Alphabetical OrderSyntaxZOOm:ZOOM1:SCAle <NR3>ZOOm:ZOOM1:SCAle?Arguments<NR3> is the amount of expansion in the horizon

Commands Listed in Alphabetical Order2-378 MSO2000B, DPO2000B, M SO2000 and DPO2000 Series Oscilloscopes Programmer Manual

Status and EventsThe oscilloscope provides a status and event reporting system for the Ethernet,GPIB (with the TEK-USB-488 Adapter), and USB interfac

Status and EventsTable 3-1: SESRBit FunctionsBit F unction7 (MSB) PON Power On. Shows that the oscilloscope was powered on.On completion, the diagnost

Status and EventsTable 3-2: SBR Bit Functions (cont.)Bit Function4MAVMessage Available. Shows that output is availablein the Output Queue.3————Not use

Status and EventsUse the *SRE command to set the SRER. Use the *SRE? query to read theregister. The RQS bit remains set to one until either the Status

Status and EventsRead the Event Queue with the EVENT? query (which returns only the eventnumber), with the EVMSG? query (which returns the event numbe

Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiariesor suppliers, and are protected by na

Command GroupsTable 2-24: Mark CommandsCommand DescriptionMARK Move to the next or p revious mark on thewaveform or returns a ll learnable settingsfro

Status and EventsFigure 3-6: Status and Event Handling ProcessWhen an event occurs, a signal is sent to the DESER (1). If that type of eventis enabled

Status and EventsSynchronization MethodsOverviewAlthough most commands are completed almost immediately after being receivedby the oscilloscope, some

Status and EventsFor example, a typical application m ight involve acquiring a single-sequencewaveform and then taking a measurement on the acquired w

Status and EventsThesamecommand sequence using the *WAI command for synchronizationlooks like this:/* Set up conditional ac quisition */ACQUIRE:STATE

Status and Eventsmany commands to the input buffer. The controller is still tied up though, andthe repeated BUSY? query will result in bus traffic.Usin

Status and EventsThesamecommand sequence using the *OPC command for synchronizationlooks like this/* Set up conditional acquisition */ACQUIRE:STATE OF

Status and Events/* Wait until the acquis ition is complete */*OPC?/* Take amplitude measurement */MEASUREMENT:IMMED:VALUE?This is the simplest approa

Status and EventsTable 3-4: Command Error Messages (CME Bit 5) (cont.)Code Message108 Parameter not allowed109 Missing parameter110Command header erro

Status and EventsTable 3-5: Execution Error Messages (EXE B it 4) (cont.)Code Message253Corrupt media254Media full255Directory full256File name not fo

Status and EventsTable 3-5: Execution Error Messages (EXE Bit 4) (cont.)Code Message2220 Measurement error, No valid edge - No arm cross2221 Measureme

Command GroupsMath Command GroupUse the commands in the Math Command Group to create and define a mathwaveform. Use the available math functions to defi

Status and EventsDevice ErrorThe following table lists the device errors that can occur d uring oscilloscopeoperation. These errors may indicate that

Status and EventsTable 3-8: Execution Warning Messages (EXE Bit 4) (cont.)Code Message543 Measurement warning, Low resolution544 Measurement warning,

Status and Events3-18 MSO2000B, DPO2000B, MSO2000 and DPO2000 Series Oscilloscopes Programmer Manual

Appendix A: Character SetMSO2000B, DPO2000B, MSO2000 and DPO2000 Series Oscilloscopes Programmer Manual A-1

Appendix A: Character SetA-2 MSO2000B, DPO2000B, MSO2000 and DPO2000 Series Oscilloscopes Programmer M anual

Appendix B: Waveform Data in MSO/DPO2000B andMSO/DPO2000 Series InstrumentsAn analog channel of an MSO/DPO2000B and MSO/DPO2000 seriesinstrument has a

Appendix B: Waveform Data in MSO/DPO2000B and MSO/DPO2000 Series InstrumentsComposition of WaveformDataThe MSO/DPO2000/B series introduces the concept

Appendix B: Wa veform Data in MSO/DPO2000B and MSO/DPO2000 Series InstrumentsCOMPOSITE_YTCOMPOSITE_YT, COMPOSITE_ENVSINGULAR_YTThe composition of the

Appendix B: Waveform Data in MSO/DPO2000B and MSO/DPO2000 Series Instrumentsreduced resolution waveform. The filtering frequency of the full resolution

Appendix B: Wa veform Data in MSO/DPO2000B and MSO/DPO2000 Series InstrumentsQuerying AcquisitionPeak Detect Data from theInstrument1. Use the DATa:CO

Command GroupsTable 2-25: Math Commands (cont.)CommandDescriptionMATH[1]:SPECTral:NYQUISTFreq? Returns the Nyquist frequency of the FFTmath waveformMA

Appendix B: Waveform Data in MSO/DPO2000B and MSO/DPO2000 Series Instrumentsturned on. Use the WFMOutpre:RECOrdlength? query to determine the a ctualr

Appendix C: Reserved WordsThis is a list of reserved words for your instrument. Capital letters identify therequired minimum spelling.*CAL*CLS*DDT*ESE

Appendix C: Reserved WordsDATABitsDATEDATEPrintDATaDAllDBDCDECimalDEFLTDEFaultDEFineDEGAUssDEGreesDELEteDELIMiterDELTaDELTatimeDELayDELayedDELeteDELta

Appendix C: Reserved WordsLETTERLEVelLFLFRejLINLINELINEArLINEPeriodLISTLOCkLOGLOGICLOGIcLOGicLOOPLOWLOWLimitLOWerthresholdLSBMAGMAINMAInMAIn]MARKMARKS

Appendix C: Reserved WordsSAMPLERateSAMPLEpointSAMpleSAVeSCANSCAleSCLKSCREENSCREenSDATASEARCHSEARCHtotriggerSECAMSECondsSELectSELectedSEQuenceSERIALnu

Appendix D: Application Module-enabled CommandsThis table lists the c ommands that become available with installation of anapplication module.MSO2000B

Appendix D: Application Module-enabled CommandsApplication ModuleCommandsAutomotive Serial Triggering and Analysis Module. Enables triggering on packe

Appendix D: Application Module-enabled CommandsApplication M oduleCommandsDPO2COMP Computer Serial Triggering and Analysis Module. Enables triggering

Appendix D: Application Module-enabled CommandsApplication ModuleCommandsDPO2EMBD Embedded Serial Triggering and Analysis Module. Enables triggering o

Appendix E: Search and Trigger Command SequenceExamplesThe following are some example command sequences that show a variety ofdifferent sear ches and

Command GroupsTable 2-26: Measurement Commands (cont.)CommandDescriptionMEASUrement:IMMed:DELay? Returns information about the immediatedelay measurem

Appendix E: Search and Trigger Command Sequence ExamplesCommand Comment:TRIGger:A:TYPe EDGE Specifies that this will be an edge trigger (trigger will o

Appendix E: Search and Trigger Command Sequence ExamplesCommand Comment*RST Resets the oscilloscope. Wait for the reset to complete(approximately 3 se

Appendix E: Search and Trigger Command Sequence ExamplesE-4 MSO2000B, DPO2000B, MSO2000 and DPO2000 Series Oscilloscopes Programmer Manual

IndexAACQuire:MAXSamplerate?, 2-59ACQuire:MODe, 2-59ACQuire:NUMACq?, 2-60ACQuire:NUMAVg, 2-61ACQuire:STATE, 2-61ACQuire:STOPAfter, 2-63ACQuire?, 2-59A

IndexC*CAL?, 2-95CALibrate:FACtory, 2-95CALibrate:FACtory:STATus?, 2-96CALibrate:INTERNal, 2-96CALibrate:INTERNal:STARt, 2-96CALibrate:INTERNal:STATu

Index*DDT, 2-134DESE, 2-135DIAg:LOOP:OPTion, 2-135DIAg:LOOP:OPTion:NTIMes, 2-136DIAg:LOOP:STOP, 2-136DIAg:RESUlt:FLAg?, 2-137DIAg:RESUlt:LOG?, 2-137DI

IndexLLANGuage, 2-172LOCk, 2-172*LRN?, 2-173MMark Command Group, 2-23MARK, 2-174MARK:CREATE, 2-174MARK:DELEte, 2-175MARK:FREE?, 2-175MARK:SELected:END

IndexMiscellaneousCommand Group, 2-29NNEWpass, 2-219O*OPC, 2-220PPASSWord, 2-221PICTBridge:DATEPrint, 2-221PICTBridge:DEFault, 2-222PICTBridge:IDPrint

IndexSEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:LIN:DATa:VALue, 2-257SEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:LIN:ERRTYPE, 2-257SEARCH:SEA

IndexSEARCH:SEARCH<x>:TRIGger:A:RUNT:WHEn, 2-276SEARCH:SEARCH<x>:TRIGger:A:RUNT:WIDth, 2-277SEARCH:SEARCH<x>:TRIGger:A:SETHold:CLOCk

Command GroupsTable 2-26: Measurement Commands (cont.)CommandDescriptionMEASUrement:MEAS<x>:MEAN?Returns the mean value accumulated sinc ethe la

IndexTRIGger:A:BUS:B<x>:RS232C:TX:DATa:SIZe, 2-310TRIGger:A:BUS:B<x>:RS232C:TX:DATa:VALue, 2-310TRIGger:A:BUS:B<x>:SPI:CONDition, 2-

IndexUSBTMC:SERIALnumber?, 2-350USBTMC:VENDORID:DECimal?, 2-350USBTMC:VENDORID:HEXadecimal?, 2-350VVERBose, 2-351Vertical Command Group, 2-47W*WAI, 2-

Command GroupsTable 2-26: Measurement Commands (cont.)CommandDescriptionMEASUrement:MEAS<x>:SOUrce<x> Sets or returns the source for the s

Command GroupsTable 2-27: Miscellaneous Commands (cont.)CommandDescriptionLOCk Sets or returns the front panel lock state*LRN? Returns a listing of o

Command GroupsTable 2-28: PictBridge Commands (cont.)CommandDescriptionPICTBridge:IDPrintEnables or disables printing the o scilloscopemodel and seria

Command GroupsTable 2-29: Save and Recall Commands (cont.)CommandDescriptionSAVe:IMAGe:LAYout Sets or returns the layout to use for savedscreen images

Command GroupsSearch CommandGroupUse the commands in the Search Commands Group to seek out information inwaveform records.Search CommandsCommand Descr

Table of ContentsGetting Started ... ... ... ... ... 1-1Setting U

Command GroupsSearch Commands (cont.)Command DescriptionSEARCH:SEARCH<x>:TRIGger:A:BUS:B<x>:I2C:ADDRess:MODeSets or returns the I2C addres

Command GroupsSearch Commands (cont.)Command DescriptionSEARCH:SEARCH<x>:TRIGger:A:EDG E:SOUrceSets or returns the source waveform for anedge se

Command GroupsSearch Commands (cont.)Command DescriptionSEARCH:SEARCH<x>:TRIGger:A:LOGIc:THReshold:REF<x>Sets or returns the reference w a

Command GroupsSearch Commands (cont.)Command DescriptionSEARCH:SEARCH<x>:TRIGger:A:SETHold:THReshold:REF<x>Sets or returns the trigger sea

Command GroupsTable 2-30: Status and Error Commands (cont.)CommandDescription*ESE Sets or returns the bits in the Event StatusEnable Register*ESR? Ret

Command Groupsset the threshold voltage levels using TRIGger:A:LEVel:AUXin,TRIGger:A:LEVel:CH<x>,orTRIGger:A:LEVel:D<x>.Logic TriggerLogic

Command GroupsRunt triggering lets you trigger on a pulse amplitude that crosses one thresholdbut fails to cross a second threshold before recrossing

Command GroupsTable 2-31: Trigger CommandsCommandDescriptionTRIGgerForces a trigger event tooccurTRIGger:FREQuency?Returns the available triggerfreque

Command GroupsTable 2-31: Trigger Commands (cont.)CommandDescriptionTRIGger:A:BUS :B<x>:LIN:ID entifier:VALue Sets or returns the binaryaddress s

Command GroupsTable 2-31: Trigger Commands (cont.)CommandDescriptionTRIGger:A:BUS:B <x >:SPI:D ATa{:OUT|:M OSI}:VALue Sets or returns the binary

Table of ContentsCommands Listed in Alphabetical Order ... 2-59Status and Events ...

Command GroupsTable 2-31: Trigger Commands (cont.)CommandDescriptionTRIGger:A:LOGIc:INPut:C H<x> Specifies or returns thelogic setting for the sp

Command GroupsTable 2-31: Trigger Commands (cont.)CommandDescriptionTRIGger:A:PULse:CLAss Sets or returns the type ofpulse on which to triggerTRIGger:

Command GroupsTable 2-31: Trigger Commands (cont.)CommandDescriptionTRIGger:A:SETHold:DATa?Returns the voltagethreshold and data sourcefor the setup/h

Command GroupsTable 2-31: Trigger Commands (cont.)CommandDescriptionTRIGger:A:VIDeo:POLarity Sets or returns the polarity ofthe A video triggerTRIGger

Command GroupsTable 2-32: Ve rtical Commands (cont.)Command DescriptionAUXin:PRObe:ID:SERnumber? Returns the serial number of the probe thatis attache

Command GroupsTable 2-32: Ve rtical Commands (cont.)Command DescriptionCH<x>:PRObe:ID:SERnumber? Returns the serial number of the probe thatis a

Command GroupsTable 2-32: Ve rtical Commands (cont.)Command DescriptionSELect:BUS<x> Turns on or off the specified bus waveformor returns whether

Command GroupsNOTE. The source w aveform (as specified by the DATa:SOUrce) must be turnedon for the following queries to return a response:CURVe?DATa:C

Command GroupsEach data valuerequires two to seven characters. This includes one to fivecharacters to represent the value, another charac t er, if the

Command Groupscommand. Next,specify the fi rst data point within the waveform record. Forexample, when you set DATa:STARt to 1, data points will be sto

Getting StartedThis manual explains the use of commands for remotely controlling youroscilloscope. With this information, you can write computer progr

Command GroupsTransferring WaveformData to the OscilloscopeYou can transfer waveforms to the oscilloscope from an external controller usingthe followi

Command GroupsTable 2-34: Waveform Transfer Commands (cont.)CommandDescriptionDATa:STOP Sets or returns the ending data point inwaveform transferWA VF

Command GroupsTable 2-34: Waveform Transfer Commands (cont.)CommandDescriptionWFMInpre:YZEroSets or returns the vertical offset of theincoming wavefor

Command GroupsTable 2-34: Waveform Transfer Commands (cont.)CommandDescriptionWFMOutpre:YMUlt? Returns the vertical scale factor per digitizinglevel f

Command Groups2-58 MSO2000B, DPO2000B, MSO2000 and DPO2000 Series Oscilloscopes Programmer Manual

Commands Listed in Alphabetical OrderACQuire? (Query Only)Returns the following current acquisition parameters:Stop afterAcquisition stateModeNumber o

Commands Listed in Alphabetical OrderWaveforms are the displayed d ata point values taken from acquisition intervals.Each acquisition interval represe

Commands Listed in Alphabetical Orderstart acquisitions again, it will continue from 5000. The number will reset to 0only if you change the horizontal

Commands Listed in Alphabetical Ordersingle sequence acquisition will be started. If the last acquisition was continuous,a new continuous acquisition

Commands Listed in Alphabetical OrderACQuire:STOPAfterSets or returns whether the oscilloscope continually acquires acquisitions oracquires a single s

Getting StartedDPO2022B – 2 00 MHz, 2 channelSetting Up Remote Communications HardwareYou can remotely communicate between your oscilloscope and PC vi

Commands Listed in Alphabetical OrderArgumentsOFF turns aliasexpansion off. If a defined alias is sent when ALIas is off, acommand error (110) will be

Commands Listed in Alphabetical OrderRelated CommandsALIas[:STATE]ArgumentsThe first <QString> is the alias label.This label cannot be a command

Commands Listed in Alphabetical OrderGroupAliasSyntaxALIas:DELEte:ALLRelated CommandsALIas:DELEte, ALIas:DELEte[:NAMe]ExamplesALIAS:DELETE:ALL deletes

Commands Listed in Alphabetical OrderExamplesALIAS[:STATE]OFFturns the command alias feature off.ALIAS[:STATE]? returns 0 when the alias feature is of

Commands Listed in Alphabetical OrderAUTOSet:ENAbleEnables or disables the autoset.GroupMiscellaneousSyntaxAUTOSet:ENAble {OFF|ON}AUTOSet:ENAble?Relat

Commands Listed in Alphabetical OrderExamplesAUXIN:PROBE? might returnAUXIN:PROBE:ID:TYPE "No ProbeDetected";SERNUMBER "";:AUXIN:P

Commands Listed in Alphabetical OrderAUXin:PRObe:DEGAUss (No Query Form)Starts a degauss/autozero cycle on a TekVPI current probe attached to the A ux

Commands Listed in Alphabetical OrderArguments<NR3> is the probe range, which is probe dependent.AUXin:PRObe:GAINSets or returns the gain factor

Commands Listed in Alphabetical OrderGroupVerticalSyntaxAUXin:PRObe:RESistance?ExamplesAUXin:PRObe:RESistance? might return :AUXin:PR OBE:RESISTANCE1.

Commands Listed in Alphabetical OrderBUSSets or returns the parameters for each bus. These parameters affect either theSerial Trigger Setup or the Bus

Getting StartedTo view or change the Ethernet settings on your oscilloscope, do the following:1. On the front panel, push Utility.2. Push Utility Page

Commands Listed in Alphabetical OrderSyntaxBUS:B<x>:CAN:PRObe {CA NH|CANL|RX|TX|DI FFerential}BUS:B<x>:CAN:PRObe?ArgumentsCANH specifies th

Commands Listed in Alphabetical OrderArgumentsCH1–CH4 is the analog c hannel to use as the data source.D0–D15 is the digital channel to use as the dat

Commands Listed in Alphabetical OrderOFF does not include the read/write bit in the address.ON includes the read/write bit in the address.ExamplesBUS:

Commands Listed in Alphabetical OrderArgumentsCH1–CH4 specifies the analog channel to use as the I2C SDATA source.D0–D15 specifies the digital channel t

Commands Listed in Alphabetical OrderConditionsThis command requires a DPO2AUTO application m odule.GroupBusSyntaxBUS:B<x>:LIN:IDFORmat {NOPARit

Commands Listed in Alphabetical OrderConditionsThis command requires a DPO2AUTO application module.GroupBusSyntaxBUS:B<x>:LIN:SAMPLEpoint <NR

Commands Listed in Alphabetical OrderGroupBusSyntaxBUS:B<x>:LIN:STANDard {V1X|V2X|MIXed}BUS:B<x>:LIN:STANDard?ArgumentsV1X sets the LIN st

Commands Listed in Alphabetical OrderArgumentsEIther specifies either rising or falling edge as the clock edge.RISing specifies the rising edge as the c

Commands Listed in Alphabetical OrderSyntaxBUS:B<x>:PARallel:WIDth <NR1>BUS:B<x>:PARallel:WIDth?Arguments<NR1> is the number o

Commands Listed in Alphabetical OrderBUS:B<x>:RS232C:DATABitsSets or returns the number of RS232 data bits for bus <x>, where x is the bus